Kids Classical Music

Articles · Lessons and practice

How to put together a flute and a clarinet

Updated 2026-11-14

Keys bend when a flute or clarinet is put together or taken apart in a rush. A bent key or rod can stop a note from sounding, and a repair costs money. This page shows how to assemble each one with care, step by step.

Before you start

  • Wash and dry the hands.
  • Open the case flat on a table or the floor, not on a lap.
  • Hold each part where there are no keys.
  • Twist the parts together. Do not push them straight on or rock them.

The flute

A flute has three parts.

Part What it looks like
Headjoint The short top piece, with the lip plate and the hole you blow across
Body The long middle piece, with most of the keys
Footjoint The short bottom piece, with a few keys and a rod

Put it together.

  1. Headjoint into the body. Hold the body at the top end, where there are no keys. Twist the headjoint in.
  2. Line up the headjoint. Turn it so the blowing hole lines up with the first key on the body.
  3. Footjoint onto the body. Hold the footjoint at the end, away from the keys. Twist it on.
  4. Line up the footjoint. Turn it so its rod points to the middle of the last key on the body.

Some beginner flutes have small marks on the parts to line up. If yours does, use them. The teacher may adjust the line-up to fit your child’s hands.

The clarinet

A clarinet has five main parts, plus a reed and a ligature that holds the reed on.

Part What it looks like
Mouthpiece The top piece you blow into
Barrel A short piece below the mouthpiece
Upper joint The left-hand section, with rings and keys
Lower joint The right-hand section, the longest piece
Bell The flared end at the bottom

Many teachers put a clarinet together from the bottom up.

  1. Bell onto the lower joint. Hold the lower joint near the bottom, away from the rods. Twist the bell on.
  2. Upper joint onto the lower joint. This is the step to watch. Hold the upper joint in the left hand and press down the rings. That lifts a small key on the side, called the bridge key. Twist the joints together, and line up the two halves of the bridge key so they meet.
  3. Barrel onto the upper joint. Twist it on.
  4. Mouthpiece onto the barrel. Twist it on. The flat side faces the back of the clarinet, where the thumb hole is.
  5. Reed and ligature last. Read how to make a first sound on the clarinet.

If the bridge key is not lifted, the two halves can hit and bend. If the joints go together but some low notes will not play, the bridge key may be out of line.

Cork grease

The joints on a clarinet are wrapped in cork. If a joint is hard to twist, rub a small amount of cork grease on the cork. If it twists with no trouble, skip the grease. Too much makes the joints loose. Most flutes have metal joints with no cork. Never put cork grease on a flute.

Taking them apart

Take each one apart in the reverse order, with the same twisting motion. On the clarinet, press the rings again before you pull the upper and lower joints apart.

Swab the inside after each use. Pull the cloth through each part to dry it, then lay each part back in its spot in the case.

Common mistakes

  • Holding the keys. Squeezing the keys or rods bends them.
  • Forgetting the bridge key. A common clarinet mistake.
  • Forcing a joint. If a part will not go on, stop. Ask the teacher.
  • Leaving it out. A flute or clarinet on a chair or bed is easy to sit on. Put it in the case.

Games

Name the parts. Lay the parts out. Your child names each one before putting it together.

Line-up check. After assembly, your child looks down the length of the flute or clarinet and checks the line-up.

Read parts of the flute, parts of the clarinet, and band instrument care.

Read how to make a first sound on the flute, the flute for kids, and the clarinet for kids.

Sources

Use it with your kids

Print a listening page, a practice chart, or a composer fact sheet. Or try a tool, such as the composer timeline or the piece picker.

Free printablesTools